nday
CVE-2026-98749

tty: serial: max3100: shut down timer before freeing port

Linux / Linux

CVE 공개: . nday가 아직 패치 근거를 수집하지 않았습니다. 패치가 없다는 뜻은 아닙니다. PoC 출처 4곳 모두 미등재. CISA KEV 미등재.

tags productLinux kernel product typeoperating system
why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

Linux kernel
affected products in the CVE record: Linux · Linux
operating system
affected products in the CVE record: Linux · Linuxthe product type of Linux kernel in nday's product registry
현재 단계
DIS
공개
CVSS
점수 없음

생명주기

가로축 UTC. 점 = 분 단위, 넓은 막대 = 날짜만, 빈 표시 = 불명 또는 추정.
시점 알 수 없음
DIS공개
10-18T15:47Z
PAT패치
아직 기록 없음
ANA분석
아직 기록 없음
POCPoC
아직 기록 없음
ITW악용
아직 기록 없음
KEVKEV
아직 기록 없음

요약

In the Linux kernel, the following vulnerability has been resolved:

tty: serial: max3100: shut down timer before freeing port

max3100_shutdown() stops the polling timer but returns early during system suspend. If the SPI device is unbound before resume, the serial core does not call max3100_shutdown() again, so max3100_remove() frees the port while the timer remains armed. max3100_timeout() may then access the freed port and re-arm the timer.

Add final timer teardown to max3100_remove() and use timer_shutdown_sync() to prevent a racing callback from re-arming it. Also free the IRQ and destroy the workqueue there before freeing the port. Keep timer_delete_sync() in max3100_shutdown() so that a subsequent open() can re-arm the timer.

The workqueue is created before request_irq() and destroyed on both request_irq() failure and normal shutdown. Its presence at remove thus identifies the IRQ left registered when suspend bypasses shutdown.

Free the IRQ before destroying the workqueue, in both max3100_shutdown() and max3100_remove(), and cancel the pending work in between. free_irq() waits for a running interrupt handler to finish and no new handler can start afterwards, so a racing handler cannot queue work on a workqueue that is being destroyed; the force_end_work check in max3100_dowork() only narrows that window, as a handler delayed between the check and queue_work() could still run after the teardown has cleared the workqueue pointer. Cancelling the work also keeps destroy_workqueue() from waiting on a queued work item in case remove() ever runs while the freezable workqueue is still frozen, e.g. device removal during the resume window, before workqueues are thawed.

This issue was found by an in-house static analysis tool.

Original text of the CVE record (cvelist), shown as published.

이벤트 로그

+DISCVE 공개

CVE 레코드 공개(CNA: Linux).

출처 cvelist · nday 일괄 수집 · 원본
{
  "id": 458033,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-98749",
  "occurred_at": "2026-10-18T15:47:34.347Z",
  "observed_at": "2026-11-13T05:40:20.493151Z",
  "is_backfill": true,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-10-18T15:47:34.347Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

연구자 논의

최근 7일간 연구자 0명이 언급

목록의 연구자가 X에서 이 CVE를 언급한 게시물입니다. 원문 그대로 보여 주며 nday는 검증하지 않습니다.

명단의 연구자가 X에서 이 CVE를 언급한 게시물은 아직 수집되지 않았습니다.

Discussion

0 comments

No comments yet.