nday
CVE-2026-99614

drm/nouveau/nvkm: clear use.enabled when subdev init fails

Linux / Linux

Disclosed . nday has no fix record for it yet; that does not mean no patch exists. None of the four PoC sources lists it. Not in CISA KEV.

tags productLinux kernel product typeoperating system
why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

Linux kernel
affected products in the CVE record: Linux · Linux
operating system
affected products in the CVE record: Linux · Linuxthe product type of Linux kernel in nday's product registry
stage
DIS
disclosed
cvss
no score yet

Lifecycle

x axis UTC; dot = exact minute, wide bar = date only, hollow = unknown or inferred.
time unknown
DISdisclosed
11-20T05:49Z
PATpatch
no record yet
ANAanalysis
no record yet
POCPoC
no record yet
ITWexploited
no record yet
KEVKEV
no record yet

Summary

In the Linux kernel, the following vulnerability has been resolved:

drm/nouveau/nvkm: clear use.enabled when subdev init fails

On Kepler boards without the video decode falcon firmware installed (msvld/mspdec/msppp), every other VA-API decode attempt binds to an engine with no ucode loaded. The submitted work never completes, which leads to a context switch timeout, a channel recovery that cannot reset the engine, and eviction waits on fences that never signal. The process ends up stuck in D state, or killed by SIGBUS when it touches a buffer evicted after the wait times out:

msvld: unable to load firmware data

msvld: init failed, -19
fifo: SCHED_ERROR 0a [CTXSW_TIMEOUT]
vo[5444]: channel 14 killed!
WARNING: drivers/gpu/drm/nouveau/nvkm/engine/fifo/runl.c:117 at nvkm_runl_rc+0x2a4/0x3b0 [nouveau]
[TTM] Buffer eviction failed
WARNING: drivers/gpu/drm/nouveau/nouveau_bo.c:1092 at nouveau_bo_move_ntfy.part.0+0x9b/0x100 [nouveau]

Tracing nvkm_subdev_ref() and nvkm_subdev_init_() shows the pattern: a reference taken with enabled=0 runs nvkm_falcon_init(), which returns -ENODEV; the next reference sees enabled=1 and succeeds without running it.

Clear use.enabled when init() fails, so that every later reference retries init and fails cleanly. The other readers of use.enabled are fini() handlers that use it to skip teardown, which they now also do after a failed init().

On a GK107 (Quadro K1100M) without video firmware, playing H.264 with mpv --hwdec=auto: without this patch the GPU channel is killed within a minute and mpv hangs; with it, VA-API decoder creation fails, mpv falls back to software decoding, and no faults are logged.

Original text of the CVE record (cvelist), shown as published.

Event log

+DISdisclosed

CVE record published by Linux.

src cvelist · nday , observed live · raw
{
  "id": 494656,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-99614",
  "occurred_at": "2026-11-20T05:49:36.126Z",
  "observed_at": "2026-11-20T06:00:12.589971Z",
  "is_backfill": false,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-11-20T05:49:36.126Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

Researcher discussion

0 researchers mentioned this in the last 7 days

Posts on X by researchers on nday's list that mention this CVE, shown as posted. nday does not check them.

nday has not collected any post on X by listed researchers that mentions this CVE.

Discussion

0 comments

No comments yet.