nday
CVE-2026-93209

Bluetooth: hci_core: use skb_get() instead of skb_clone() for req_skb

Linux / Linux

Disclosed . nday has no fix record for it yet; that does not mean no patch exists. None of the four PoC sources lists it. Not in CISA KEV.

tags productLinux kernel product typeoperating system
why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

Linux kernel
affected products in the CVE record: Linux · Linux
operating system
affected products in the CVE record: Linux · Linuxthe product type of Linux kernel in nday's product registry
stage
DIS
disclosed
cvss
no score yet

Lifecycle

x axis UTC; dot = exact minute, wide bar = date only, hollow = unknown or inferred.
time unknown
DISdisclosed
09-24T15:10Z
PATpatch
no record yet
ANAanalysis
no record yet
POCPoC
no record yet
ITWexploited
no record yet
KEVKEV
no record yet

Summary

In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: hci_core: use skb_get() instead of skb_clone() for req_skb

BT enable fails intermittently with -ETIMEDOUT (-110). The kernel log shows the HCI Read Local Version command was sent and the firmware replied with status 0x00 (logged by hci_req_cmd_complete() BT_DBG), but the waiter in __hci_cmd_sync_sk() never woke up and timed out after 10 s:

bluetooth hci0: Opcode 0xfc00              // __hci_cmd_sync_sk
bluetooth hci0: opcode 0xfc00 plen 1       // hci_cmd_sync_add
bluetooth hci0: skb len 4                  // hci_cmd_sync_alloc
bluetooth hci0: length 1                   // hci_req_sync_run
Bluetooth: hci0 cmd_cnt 1 cmd queued 1     // hci_cmd_work
Bluetooth: hci0 type 1 len 4               // hci_send_frame
Bluetooth: opcode 0xfc00 status 0x00       // hci_req_cmd_complete
<-- req_skb NULL: req_complete_skb not set,
    hci_cmd_sync_complete() never called,
    req_status stays HCI_REQ_PEND            -->
<-- 10 s later: wait_event_interruptible_timeout expires -->
bluetooth hci0: end: err -110              // __hci_cmd_sync_sk

The root cause is that hci_send_cmd_sync() clones the sent command into hdev->req_skb so that hci_req_cmd_complete() can locate the registered completion callback. Under memory pressure this skb_clone() fails, leaving hdev->req_skb NULL. The firmware reply is received and processed, but hci_req_cmd_complete() finds NULL req_skb, so hci_cmd_sync_complete() is never called, req_status stays HCI_REQ_PEND, and the waiter times out with -ETIMEDOUT.

req_skb is only used to read bt_cb(skb)->hci callbacks and opcode -- it is never modified. Replace skb_clone() with skb_get(), which simply increments the reference count of hdev->sent_cmd without allocating new memory and therefore cannot fail.

This issue was first observed as a use-after-free in ttyport_close() when ttyport_open() failed, which was investigated in an earlier patch series [1]. That investigation led to the discovery of the true root cause described above.

[1] https://lore.kernel.org/all/[email protected]/

Original text of the CVE record (cvelist), shown as published.

Event log

+DISdisclosed

CVE record published by Linux.

src cvelist · nday , bulk import · raw
{
  "id": 455087,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-93209",
  "occurred_at": "2026-09-24T15:10:32.762Z",
  "observed_at": "2026-11-13T05:40:18.592119Z",
  "is_backfill": true,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-09-24T15:10:32.762Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

Researcher discussion

0 researchers mentioned this in the last 7 days

Posts on X by researchers on nday's list that mention this CVE, shown as posted. nday does not check them.

nday has not collected any post on X by listed researchers that mentions this CVE.

Discussion

0 comments

No comments yet.