nday
CVE-2026-80999

net: dsa: realtek: use gpiod_set_value_cansleep for reset GPIO

Linux / Linux

Disclosed . nday has no fix record for it yet; that does not mean no patch exists. None of the four PoC sources lists it. Not in CISA KEV.

tags productLinux kernel product typeoperating system
why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

Linux kernel
affected products in the CVE record: Linux · Linux
operating system
affected products in the CVE record: Linux · Linuxthe product type of Linux kernel in nday's product registry
stage
DIS
disclosed
cvss
no score yet

Lifecycle

x axis UTC; dot = exact minute, wide bar = date only, hollow = unknown or inferred.
time unknown
DISdisclosed
09-11T19:42Z
PATpatch
no record yet
ANAanalysis
no record yet
POCPoC
no record yet
ITWexploited
no record yet
KEVKEV
no record yet

Summary

In the Linux kernel, the following vulnerability has been resolved:

net: dsa: realtek: use gpiod_set_value_cansleep for reset GPIO

rtl83xx_reset_assert() and rtl83xx_reset_deassert() are only called from the probe path, which may sleep and is not timing-critical. When the reset GPIO is provided by a sleeping controller such as an I2C I/O expander, gpiod_set_value() warns:

WARNING: drivers/gpio/gpiolib.c:4030 at gpiod_set_value+0x44/0x80, CPU#1: kworker/u16:4/61
Hardware name: B&O MAP CA33 Rev f (UNKNOWN) (DT)
Workqueue: events_unbound deferred_probe_work_func
pc : gpiod_set_value+0x44/0x80
lr : rtl83xx_probe+0x1d8/0x3a0
Call trace:
 gpiod_set_value+0x44/0x80 (P)
 rtl83xx_probe+0x1d8/0x3a0
 realtek_mdio_probe+0x24/0xa0
 mdio_probe+0x38/0x78
 really_probe+0xc4/0x3e0
 __driver_probe_device+0x15c/0x1b8
 driver_probe_device+0xb4/0x120
 __device_attach_driver+0xb8/0x1a0
 bus_for_each_drv+0x88/0xf0
 __device_attach+0xa0/0x1d8
 device_initial_probe+0x54/0x68
 bus_probe_device+0x38/0xa0
 deferred_probe_work_func+0xb8/0x120
 process_one_work+0x184/0x4e8
 worker_thread+0x188/0x308
 kthread+0x130/0x150
 ret_from_fork+0x10/0x20

Switch both helpers to gpiod_set_value_cansleep() so such a reset GPIO can be used without triggering the warning.

The reset GPIO has been driven with the non-sleeping gpiod_set_value() since the driver was added in v4.19. The call has since been refactored across several files - from realtek-smi.c / realtek-mdio.c into the common rtl83xx.c module and then into the rtl83xx_reset_assert() and rtl83xx_reset_deassert() helpers (both in v6.9). This patch therefore applies as-is only to kernels that carry those helpers (v6.9+); older stable kernels need the same gpiod_set_value_cansleep() conversion at the corresponding open-coded call sites.

Original text of the CVE record (cvelist), shown as published.

Event log

+DISdisclosed

CVE record published by Linux.

src cvelist · nday , bulk import · raw
{
  "id": 446919,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-80999",
  "occurred_at": "2026-09-11T19:42:53.509Z",
  "observed_at": "2026-11-13T05:40:11.364625Z",
  "is_backfill": true,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-09-11T19:42:53.509Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

Researcher discussion

0 researchers mentioned this in the last 7 days

Posts on X by researchers on nday's list that mention this CVE, shown as posted. nday does not check them.

nday has not collected any post on X by listed researchers that mentions this CVE.

Discussion

0 comments

No comments yet.