nday
CVE-2026-90087

Bluetooth: do not leak an hci_conn when a second LE connect is rejected

Linux / Linux

CVE 공개: . nday가 아직 패치 근거를 수집하지 않았습니다. 패치가 없다는 뜻은 아닙니다. PoC 출처 4곳 모두 미등재. CISA KEV 미등재.

tags productLinux kernel product typeoperating system
why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

Linux kernel
affected products in the CVE record: Linux · Linux
operating system
affected products in the CVE record: Linux · Linuxthe product type of Linux kernel in nday's product registry
현재 단계
DIS
공개
CVSS
점수 없음

생명주기

가로축 UTC. 점 = 분 단위, 넓은 막대 = 날짜만, 빈 표시 = 불명 또는 추정.
시점 알 수 없음
DIS공개
09-17T16:06Z
PAT패치
아직 기록 없음
ANA분석
아직 기록 없음
POCPoC
아직 기록 없음
ITW악용
아직 기록 없음
KEVKEV
아직 기록 없음

요약

In the Linux kernel, the following vulnerability has been resolved:

Bluetooth: do not leak an hci_conn when a second LE connect is rejected

create_le_conn_complete() decides whether the failed connection is still pending by comparing it against hci_lookup_le_connect(), which returns the first LE connection in BT_CONNECT. That is the same connection only while at most one is pending.

Two can be pending. Connections created on the passive scan path sit in BT_CONNECT with HCI_CONN_SCANNING set and are invisible to hci_lookup_le_connect() until hci_le_create_conn_sync() clears the flag when their command is issued, so the -EBUSY guard in hci_connect_le() does not prevent a second connection from being queued while the first is still on the scan path. Whenever two connections are in BT_CONNECT at once, the lookup may return one connection while create_le_conn_complete() is reporting the failure of the other; the early exit then drops the error and hci_conn_failed() never runs on the connection that failed.

The controller also rejects a second HCI_OP_LE_CREATE_CONN issued while another connection creation is still outstanding, per Core Spec Vol 4, Part E. The spec calls for Command Disallowed there; the bcm43438 observed here answers with an LMP/LL error code instead, which bt_to_errno() maps to the -EPROTO (-71) in the log below.

The leaked connection stays in BT_CONNECT forever, and because hci_connect_le() refuses to dial while hci_lookup_le_connect() finds anything, every subsequent attempt to reach any peer fails with -EBUSY and no command reaches the controller at all.

Seen on a bcm43438 with two BLE peers polled on the same interval (state 5 is BT_CONNECT; both handles are UNSET ones, allocated from the ida above HCI_CONN_HANDLE_MAX):

Bluetooth: hci1: Opcode 0x2013 failed: -71

# hcitool con
        < LE 14:9C:EF:03:68:81 handle 3840 state 5 lm CENTRAL
        < LE C4:D3:6A:8C:B5:38 handle 3841 state 5 lm CENTRAL

A btmon capture across the next ten minutes of connect attempts contains no HCI_OP_LE_CREATE_CONN at all; outgoing LE connections do not recover until the adapter is reset. With this change the same scenario fails the rejected connection cleanly and further connects to both peers go through.

Ask about the connection itself instead of about the device.

Original text of the CVE record (cvelist), shown as published.

이벤트 로그

+DISCVE 공개

CVE 레코드 공개(CNA: Linux).

출처 cvelist · nday 일괄 수집 · 원본
{
  "id": 452771,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-90087",
  "occurred_at": "2026-09-17T16:06:02.872Z",
  "observed_at": "2026-11-13T05:40:16.734465Z",
  "is_backfill": true,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-09-17T16:06:02.872Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

연구자 논의

최근 7일간 연구자 0명이 언급

목록의 연구자가 X에서 이 CVE를 언급한 게시물입니다. 원문 그대로 보여 주며 nday는 검증하지 않습니다.

명단의 연구자가 X에서 이 CVE를 언급한 게시물은 아직 수집되지 않았습니다.

Discussion

0 comments

No comments yet.