nday
CVE-2026-89666

nfsd: reject out-of-range nseconds in NFSv3 SETATTR and create ops

Linux / Linux

CVE 공개: . nday가 아직 패치 근거를 수집하지 않았습니다. 패치가 없다는 뜻은 아닙니다. PoC 출처 4곳 모두 미등재. CISA KEV 미등재.

tags productLinux kernel product typeoperating system
why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

Linux kernel
affected products in the CVE record: Linux · Linux
operating system
affected products in the CVE record: Linux · Linuxthe product type of Linux kernel in nday's product registry
현재 단계
DIS
공개
CVSS
점수 없음

생명주기

가로축 UTC. 점 = 분 단위, 넓은 막대 = 날짜만, 빈 표시 = 불명 또는 추정.
시점 알 수 없음
DIS공개
09-11T19:45Z
PAT패치
아직 기록 없음
ANA분석
아직 기록 없음
POCPoC
아직 기록 없음
ITW악용
아직 기록 없음
KEVKEV
아직 기록 없음

요약

In the Linux kernel, the following vulnerability has been resolved:

nfsd: reject out-of-range nseconds in NFSv3 SETATTR and create ops

A client can send an NFSv3 SETATTR, CREATE, MKDIR, SYMLINK or MKNOD carrying an atime or mtime whose nseconds field is out of range. The value is well-formed on the wire and decodes cleanly into a valid uint32, but it is not a valid timespec64: tv_nsec must be less than NSEC_PER_SEC.

Nothing in the setattr path clamps it. notify_change() runs the time through timestamp_truncate(), which does not reduce tv_nsec below NSEC_PER_SEC when the filesystem supports nanosecond granularity (s_time_gran == 1), and the inode atime/mtime setters store it verbatim (only ctime is normalized, via inode_set_ctime_to_ts()). The un-normalized value then corrupts on-disk metadata: ext4's ext4_encode_extra_time() shifts tv_nsec left by EXT4_EPOCH_BITS, which overflows the 32-bit extra field and clobbers the seconds-epoch bits, so the stored seconds (and thus the year) are wrong on read-back. XFS with bigtime mis-stores the timestamp for the same reason.

Validate the client-supplied atime/mtime in the proc handlers and return NFS3ERR_INVAL before anything is changed. RFC 1813 lists NFS3ERR_INVAL for SETATTR and describes it as the error for a value the server 'can not store ... in its own representation'; the client maps it to EINVAL.

Checking in the proc handlers, rather than in nfsd_setattr(), keeps the rejection in front of object creation. The create operations create the object before nfsd_create_setattr() runs, so a late failure would leave the new object behind and turn a non-idempotent request into a namespace change that reports failure. The check is therefore done up front, for the create operations before the object is created.

tv_nsec is a long, so the comparison casts it to unsigned long (the same width) rather than to u32, matching timespec64_valid(). A u32 cast would truncate on 64-bit; the unsigned long cast also rejects a value that became negative when an out-of-range u32 wire nseconds was assigned to a 32-bit long.

Only client-supplied times are checked: SET_TO_SERVER_TIME requests carry no client value. The sattrguard3 ctime is deliberately left alone: an out-of-range guard simply never matches the object's ctime and yields NFS3ERR_NOT_SYNC via the existing guardtime comparison, which is the protocol-correct outcome rather than rejecting the request.

Original text of the CVE record (cvelist), shown as published.

이벤트 로그

+DISCVE 공개

CVE 레코드 공개(CNA: Linux).

출처 cvelist · nday 일괄 수집 · 원본
{
  "id": 452352,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-89666",
  "occurred_at": "2026-09-11T19:45:52.864Z",
  "observed_at": "2026-11-13T05:40:14.931471Z",
  "is_backfill": true,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-09-11T19:45:52.864Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

연구자 논의

최근 7일간 연구자 0명이 언급

목록의 연구자가 X에서 이 CVE를 언급한 게시물입니다. 원문 그대로 보여 주며 nday는 검증하지 않습니다.

명단의 연구자가 X에서 이 CVE를 언급한 게시물은 아직 수집되지 않았습니다.

Discussion

0 comments

No comments yet.