nday
CVE-2026-46148

spi: microchip-core-qspi: control built-in cs manually

Linux / Linux

に公開されました。nday はまだ修正の根拠を取得していません。修正がないという意味ではありません。4 つの PoC ソースのいずれにも未掲載です。CISA KEV には現時点で未掲載です。

why these tags

nday derives these tags by fixed rules from the facts below; NVD, the CNA and other sources do not assign them. Vocabulary and rules: ~/tags.

local
AV:L in CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H (CVSS 3.1) from NVD's analysts
no user interaction
UI:N in CVSS:3.1/AV:L/AC:L/PR:L/UI:N/S:U/C:N/I:N/A:H (CVSS 3.1) from NVD's analysts
Linux kernel
affected products in the CVE record: Linux · LinuxCPE names NVD's analysts give as vulnerable: o:linux:linux_kernel
operating system
affected products in the CVE record: Linux · LinuxCPE names NVD's analysts give as vulnerable: o:linux:linux_kernelthe product type of Linux kernel in nday's product registry
現在の段階
DIS
公開日時
CVSS 基本値
スコアなし

ライフサイクル

横軸は UTC。点=分単位、幅広の帯=日付のみ、白抜き=不明または推定。
日時不明
DIS公開
05-28T09:36Z
PAT修正
記録なし
ANA解析
記録なし
POCPoC
記録なし
ITW悪用
記録なし
KEVKEV
記録なし

概要

In the Linux kernel, the following vulnerability has been resolved:

spi: microchip-core-qspi: control built-in cs manually

The coreQSPI IP supports only a single chip select, which is automagically operated by the hardware - set low when the transmit buffer first gets written to and set high when the number of bytes written to the TOTALBYTES field of the FRAMES register have been sent on the bus. Additional devices must use GPIOs for their chip selects. It was reported to me that if there are two devices attached to this QSPI controller that the in-built chip select is set low while linux tries to access the device attached to the GPIO.

This went undetected as the boards that connected multiple devices to the SPI controller all exclusively used GPIOs for chip selects, not relying on the built-in chip select at all. It turns out that this was because the built-in chip select, when controlled automagically, is set low when active and high when inactive, thereby ruling out its use for active-high devices or devices that need to transmit with the chip select disabled.

Modify the driver so that it controls chip select directly, retaining the behaviour for mem_ops of setting the chip select active for the entire duration of the transfer in the exec_op callback. For regular transfers, implement the set_cs callback for the core to use.

As part of this, the existing setup callback, mchp_coreqspi_setup_op(), is removed. Modifying the CLKIDLE field is not safe to do during operation when there are multiple devices, so this code is removed entirely. Setting the MASTER and ENABLE fields is something that can be done once at probe, it doesn't need to be re-run for each device. Instead the new setup callback sets the built-in chip select to its inactive state for active-low devices, as the reset value of the chip select in software controlled mode is low.

Original text of the CVE record (cvelist), shown as published.

イベント履歴

+DIS公開

Linux が CVE レコードを公開。

出典 cvelist · nday が に一括取り込み · 生データ
{
  "id": 426203,
  "type": "disclosed",
  "source": "cvelist",
  "url": "https://www.cve.org/CVERecord?id=CVE-2026-46148",
  "occurred_at": "2026-05-28T09:36:04.805Z",
  "observed_at": "2026-11-13T05:39:50.021609Z",
  "is_backfill": true,
  "dedupe_key": "",
  "detail": {
    "state": "PUBLISHED",
    "date_published": "2026-05-28T09:36:04.805Z",
    "assigner_short_name": "Linux"
  }
}

Report an error

report an error or omission

Something on this page wrong or missing? Tell the editors; if they accept it, this page's revision log says so publicly. Upstream data is not changed.

研究者の投稿

過去 7 日間に 0 人の研究者が言及

リストの研究者が X でこの CVE に触れた投稿です。原文のまま表示し、nday は検証していません。

リストの研究者が X でこの CVE に触れた投稿は、まだ収集していません。

Discussion

0 comments

No comments yet.